PowerResinEu
VisiOne
VisiOne
Couldn't load pickup availability
DentaFab VisiOne Resin is a specially formulated biocompatible 3D printing resin designed for try-in digital dentures to achieve optimal fit, function, and aesthetics before delivering the final removable full or partial prosthesis. This resin provides a cost-effective solution for verifying occlusion, stability, and appearance while minimizing adjustments and remakes.
• High-precision printing for try-in dentures and validation appliances, delivering accurate margins, clean surface detail, and predictable occlusion verification.
• Superior aesthetics, offering natural translucency and shade stability for realistic denture previews and patient approval.
• Exceptional strength and wear resistance, featuring 125 MPa flexural strength to minimize breakage during chairside adjustments and trial use.
• Biocompatible, FDA- and MDR-compliant formulation, produced under ISO 13485:2016 quality management standards.
• Characterizable with composite materials, allowing gingival tinting, shade customization, and aesthetic refinement when needed.
• Suitable for a wide range of 405 nm DLP and LCD 3D printers
Find the validated printer list and recommended settings at powerresins.com.
• No surface chalking after alcohol washing.
Disclaimer: All orders shipped outside the United States are subject to import taxes, duties, and fees, which are the responsibility of the customer. Please ensure you are aware of and prepared to cover any applicable import costs when placing an international order.
You can download the full IFU by clicking here
Product Description
Product Features
- Exceptional breakeage and high wear resistance
- Flexural strenght 126 MPa standard ASTM D790-02
- Produced under ISO standarts 13485:2016
- Find here validated 3D printers list
Material Properties
Material PropertiesValueStandardTensile strength66.5 MpaASTM D638Flexural strength126 MpaASTM D790-02Flexural modulus2980 MpaASTM D790-02Shore Hardness85.7ASTM D2240Density1.14 g/cm3 at 23 CASTM D1475Viscosity2500-3000 mPa.s at 23 CDIN 53211-4ColorAçık(A1-B1) Orta(A2-A3) Bleach (BL1)
Post Process
1- Washing
After the printing is completed, wash the part as attached to the building plate with ethyl alcohol (>%90) or isopropyl alcohol (>%90) for 5 minutes. Make sure that alcohol covers the part entirely when washing. Since the Temp resin is biocompatible never wash it with the alcohol used for other resins before. Use a brush to remove uncured resin if needed. Do not over-wash, it may cause deterioration in dimensions of the part.
2- Drying
Use air-compressor to dry the washed part. Make sure that the part is dry and uncured resin is cleaned up completely. If there is still uncured resin left on the part, wash it with fresh alcohol and dry again.
3- Part Removal
Remove the printed part from the build plate using a scraping tool. Be very careful not to damage the model.
4- Post Curing 20 minutes with MEDIFIVE curing chamber at 3rd-degree light intensity Otoflash curing recommendations 126 MPa flexural strength with 10000 flashes without gas. For the multiunit implant applications if you would like to reach the PMMA level, we recommend curing with gas(nitrogen, argon). After the post curing, supports should be removed from the model cautiously and then desired sandblasting and polishing can be done.
Storage Conditions
Store the DentaFab VisiOne bottle in dark and moisture free place at room temperature (20-24 °C).
Do not forget shaking the resin well before use.
If your printer has heater, you can set the temperature at 32 °C. Otherwise, you can heat your resin by submerging in hot water for 15-20 minutes.
-
HIGH WEAR RESISTANCE
Thanks to its technical properties, PowerResins Temp has a stain-free, abrasion-resistant formulation.
-
CONSISTENT SHADES
Shades available are A1, A2, and Bleach.
-
LOW SHRINKAGE
DentaFab VisiOne has minimal shrinkage and does not change the shape after post processing.
-
BIOCOMPATIBLE
CE certified biocompatible Temporary crown resin.
